{"product_id":"bayite-dc-volt-amp-meter-5-120v-100a-hall-effect-isolated-bidirectional-current-display","title":"bayite DC Volt-Amp Meter 5–120V 100A — Hall‑Effect Isolated, Bidirectional Current Display","description":"\u003cp\u003e\u003cstrong\u003eThe bayite DC 5-120V 100A Volt Amp Meter is an isolated, through-hole Hall-effect monitor that displays DC voltage or bidirectional current up to 100A for safe, accurate system monitoring.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThis compact panel meter pairs a Hall-effect current sensor with a straightforward digital readout to track both voltage and current in DC systems. Designed for inline installation, the sensor isolates measurements from high-voltage circuitry and accepts thick conductors with a 19 mm aperture. The unit switches between voltage and ±current modes so you can read battery banks, solar arrays, motor draws, or other DC loads without touching the main power path.\u003c\/p\u003e\n\n\u003ch3\u003eHow does this meter measure current without opening the circuit?\u003c\/h3\u003e\n\n\u003cp\u003ebayite’s meter uses a through-hole Hall-effect sensor that senses magnetic fields around the conductor instead of forcing current through a shunt. Because the wire passes through the sensor aperture, there’s no break in the power line and the meter stays electrically separated from the high-voltage circuit.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eHall-effect detection reads magnetic flux around the conductor, not conductor voltage.\u003c\/li\u003e\n  \u003cli\u003e3\/4 inch (19 mm) sensor hole accommodates large gauge wires up to typical heavy-duty sizes.\u003c\/li\u003e\n  \u003cli\u003eElectrically isolated sensing reduces risk to the display and attached equipment.\u003c\/li\u003e\n  \u003cli\u003eCan register positive or negative current flow for bidirectional systems like charging\/discharging.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat voltage and current ranges will I see on the display?\u003c\/h3\u003e\n\n\u003cp\u003eThe meter shows DC voltage from 5 V up to 120 V and measures current from 0 up to 100 A. You can toggle the display to present either the present system voltage or the real-time current with a sign indicating direction when applicable.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eVoltage range: 5–120 V DC, suitable for small to medium battery systems.\u003c\/li\u003e\n  \u003cli\u003eCurrent range: 0–100 A, practical for many automotive, marine, and renewable setups.\u003c\/li\u003e\n  \u003cli\u003eDisplay modes: voltage readout or ±current readout for charging\/discharging visibility.\u003c\/li\u003e\n  \u003cli\u003eNo need for external shunt resistors—current is detected magnetically.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow do I install and get accurate readings in low-current situations?\u003c\/h3\u003e\n\n\u003cp\u003eInstallation is straightforward: route the monitored conductor through the sensor aperture and wire the display per the manual. For small currents below the meter’s original sensitivity, you can pass the same conductor through the hole multiple times; each loop multiplies the sensed signal proportionally.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eThrough-hole design makes wiring simple—no cutting of the monitored conductor required.\u003c\/li\u003e\n  \u003cli\u003eLoop the wire multiple times to increase signal strength (e.g., 10 loops turns 0.2 A into a 2.0 A equivalent signal).\u003c\/li\u003e\n  \u003cli\u003eFollow polarity and grounding guidance in installation instructions to avoid display errors.\u003c\/li\u003e\n  \u003cli\u003eMechanical mounting fits standard panel openings for compact dashboards and enclosures.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eIs this meter safe for higher-voltage DC systems and heavy wiring?\u003c\/h3\u003e\n\n\u003cp\u003eYes—the sensor’s electrical isolation protects the meter electronics from the monitored circuit and reduces safety concerns when measuring higher DC voltages. The wide aperture accepts large conductors, so you can monitor heavier cables used in battery banks, inverters, and charging systems.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eElectrical isolation keeps the display circuitry separate from the measured high-voltage line.\u003c\/li\u003e\n  \u003cli\u003e19 mm hole supports large-gauge wires commonly used in power distribution.\u003c\/li\u003e\n  \u003cli\u003eRobust sensing avoids the heat and wiring challenges of inline shunts.\u003c\/li\u003e\n  \u003cli\u003eBidirectional current readings help you confirm charging versus load conditions safely.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: installers, hobbyists, and professionals who need a compact, safe DC monitoring solution for batteries, solar arrays, vehicles, or power cabinets. If you want a panel-friendly meter that reads both voltage and bidirectional current without cutting the conductor or adding a shunt, bayite’s DC 5–120V 100A Volt Amp Meter provides a practical, isolated option with flexible installation for low- and high-current scenarios.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can this meter measure negative current?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. The hall-effect sensor detects direction and the display shows ±current for charging or discharging indications.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Do I need a shunt resistor to use this meter?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: No. The meter uses a Hall-effect through-hole sensor and reads current magnetically without a shunt.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"bayite","offers":[{"title":"Default Title","offer_id":67593737175225,"sku":"B01DDQM6Z4","price":60.84,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0822\/3765\/3177\/files\/bayite-front-panel-display.jpg?v=1790578010","url":"https:\/\/redleafauto.ca\/products\/bayite-dc-volt-amp-meter-5-120v-100a-hall-effect-isolated-bidirectional-current-display","provider":"Redleaf Auto","version":"1.0","type":"link"}