{"product_id":"lisle-injector-seal-installer-kit-11-pc-teflon-seal-tools-for-hitachi-bosch-continental-injectors-6-7-5-mm-sizing","title":"Lisle Injector Seal Installer Kit — 11 pc Teflon seal tools for Hitachi, Bosch, Continental injectors, 6 \u0026 7.5 mm sizing","description":"\u003cb\u003eLisle Injector Seal Installer Kit (11 pc) is a dedicated tool set for removing, fitting and sizing Teflon injector seals on many Hitachi, Bosch, Continental and Delphi fuel injectors used in Ford, GM and Subaru engines.\u003c\/b\u003e\n\n\u003cp\u003eThis 11-piece kit gives technicians and home mechanics the pilot cones, pushers and sizers needed to slide Teflon seals onto injector tips, push them into the retention groove and then compress the seal back to the correct outer diameter for installation into the cylinder head. Designed to work with a wide range of modern injector stems, the kit saves time and reduces the risk of nicks or misaligned seals that cause leaks or poor seating.\u003c\/p\u003e\n\n\u003ch3\u003eHow does the kit fit and install Teflon injector seals?\u003c\/h3\u003e\n\u003cp\u003eThe process starts by mounting the pilot cone on the injector tip so the new seal can be threaded over the tapered end without folding. The installer tool then pushes the seal down and seats it into the groove on the injector tip. Finally, the sizer compresses the seal back to the correct outer diameter so the injector slides into the cylinder head cleanly.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003ePilot cones guide seals onto the tip without rolling or tearing.\u003c\/li\u003e\n  \u003cli\u003ePushers seat the seal uniformly into the injector groove.\u003c\/li\u003e\n  \u003cli\u003eSizers restore the seal’s OD for proper cylinder-head fitment.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat injectors and engines is this kit compatible with?\u003c\/h3\u003e\n\u003cp\u003eThis Lisle set works on many Hitachi, Bosch, Continental and Delphi fuel injectors commonly found on Ford, GM and Subaru engines. It also supports many Ford ECO injectors and a variety of direct-injection systems introduced in the 2010s.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003eCommon GM applications: 2010+ engines including 1.4L, 1.5L, 2.0L, 2.4L, 2.5L, 3.0L, 3.6L, 4.3L, 5.3L and 6.2L.\u003c\/li\u003e\n  \u003cli\u003eSpecific GM coverage: 2010–2017 2.0L, 2.5L, 3.6L, 5.3L and 6.2L engines.\u003c\/li\u003e\n  \u003cli\u003eSubaru coverage: 2014–2019 2.0L and 2.4L turbo engines.\u003c\/li\u003e\n  \u003cli\u003eFord coverage: many 2011 and newer injectors, including many ECO designs.\u003c\/li\u003e\n  \u003cli\u003eFits injector stems with 6 mm and 7.5 mm diameters.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhy use a dedicated installer and sizer instead of improvised tools?\u003c\/h3\u003e\n\u003cp\u003eImprovised methods risk cutting or rolling thin Teflon seals, causing leaks or premature failure. The Lisle tools are shaped to protect the seal lip, keep the seal concentric, and compress to an accurate outer diameter so the injector seats correctly in the cylinder head bore.\u003c\/p\u003e\n\u003cul\u003e\n  \u003cli\u003ePrevents seal deformation that causes fuel or vacuum leaks.\u003c\/li\u003e\n  \u003cli\u003eSpeeds seal replacement with repeatable, uniform results.\u003c\/li\u003e\n  \u003cli\u003eReduces chance of damage to expensive injectors during service.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: The Lisle Injector Seal Installer Kit — 11 pc — is intended for professional technicians, independent shops and knowledgeable DIYers who service fuel injectors on modern Ford, GM and Subaru engines. If you routinely replace Teflon injector seals or rebuild injectors, this kit streamlines seal installation, protects delicate materials, and helps ensure reliable injector seating and performance. Note: Always confirm injector manufacturer and stem diameter before use and follow vehicle-specific service procedures; this tool aids mechanical installation but does not replace OEM torque, lubrication or diagnostic steps.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eFeature: Works on many Ford ECO injectors\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Does this kit fit all injector stem sizes?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: The kit fits common 6 mm and 7.5 mm injector stems; verify your injector stem diameter before use.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I use the kit on Ford ECO injectors?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes — the set works on many Ford ECO injectors, along with Hitachi, Bosch, Continental and Delphi designs.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"Lisle","offers":[{"title":"Default Title","offer_id":67585117028537,"sku":"B0FY3Q5L4P","price":172.32,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0822\/3765\/3177\/files\/lisle-injector-seal-installer-front.jpg?v=1790467850","url":"https:\/\/redleafauto.ca\/products\/lisle-injector-seal-installer-kit-11-pc-teflon-seal-tools-for-hitachi-bosch-continental-injectors-6-7-5-mm-sizing","provider":"Redleaf Auto","version":"1.0","type":"link"}