{"product_id":"totalboat-totalfair-epoxy-fairing-compound-2-quart-kit-1-1-mix-fast-sanding-marine-putty","title":"TotalBoat TotalFair Epoxy Fairing Compound 2-Quart Kit — 1:1 Mix, Fast-Sanding Marine Putty","description":"\u003cp\u003e\u003cstrong\u003eTotalBoat TotalFair Epoxy Fairing Compound is a two-part, lightweight marine epoxy putty designed to fill, fair, and shape boat surfaces above and below the waterline.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eTotalFair comes as a 2-quart kit with a foolproof 1:1 mix ratio, formulated to bond to fiberglass, wood, aluminum, steel and cast iron while remaining flexible enough to resist cracking. The compound mixes from blue and yellow into green, spreads smoothly with a creamy consistency, and holds on vertical or overhead areas so you can repair dings, gouges and voids without running. Made in the USA for boaters, TotalFair is also suitable for automotive, RV and general marine restoration tasks.\u003c\/p\u003e\n\n\u003ch3\u003eHow quickly will TotalFair be ready to sand and paint?\u003c\/h3\u003e\n\n\u003cp\u003eAt 80°F TotalFair cures fast and becomes sandable within a few hours. Typical curing time allows rapid workflows, so you can build up layers and finish the repair the same day under suitable conditions.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eSandable in about 3–4 hours at 80°F (curing speed varies with temperature).\u003c\/li\u003e\n  \u003cli\u003eFor deep or narrow repairs, apply in stages following a 6:1 width-to-depth guideline per lift.\u003c\/li\u003e\n  \u003cli\u003eUse proper PPE when sanding cured epoxy—respirator and eye protection recommended.\u003c\/li\u003e\n  \u003cli\u003eAllow full cure before applying paint systems; follow primer recommendations below.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat surfaces and locations can I use this fairing compound on?\u003c\/h3\u003e\n\n\u003cp\u003eTotalFair bonds to a wide range of marine substrates and is suitable for use above and below the waterline. Its waterproof cured finish and strong adhesion make it a good choice for hulls, decks, keels, topsides and other structural or cosmetic repairs.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eCompatible with fiberglass, wood, aluminum, steel and cast iron.\u003c\/li\u003e\n  \u003cli\u003eEffective on hulls, decks, keels, topsides and transoms—above or below waterline.\u003c\/li\u003e\n  \u003cli\u003eGood for boats, kayaks, canoes, motor vehicles, RVs and more.\u003c\/li\u003e\n  \u003cli\u003eStronger and more waterproof than typical polyester or vinylester fairing putties.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow do I mix and apply TotalFair for best results?\u003c\/h3\u003e\n\n\u003cp\u003eMix the blue and yellow components in equal parts by volume until the compound turns a uniform green—about 3–5 minutes of thorough mixing. Work with manageable quantities, shape or feather edges while still pliable, and respect the 6:1 width-to-depth guideline to avoid excessive exotherm or sinkage.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eMix ratio: 1:1 by volume; mix until uniform green color appears (3–5 minutes).\u003c\/li\u003e\n  \u003cli\u003eApply with a spreader or putty knife; works well on vertical and overhead areas.\u003c\/li\u003e\n  \u003cli\u003eFor deep repairs, build depth in stages; maintain 6:1 width-to-depth per application.\u003c\/li\u003e\n  \u003cli\u003eDo not apply gelcoat directly over cured TotalFair—use TotalBoat epoxy primer or TotalProtect first.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat compatibility and storage notes should I follow?\u003c\/h3\u003e\n\n\u003cp\u003eTotalFair is compatible with epoxy or latex primers and most marine paints after proper surface preparation. Store the kit in a controlled environment and take standard safety precautions when working with and sanding cured epoxy.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eNot recommended for gelcoat overcoat without TotalBoat epoxy primer or TotalProtect barrier coat.\u003c\/li\u003e\n  \u003cli\u003eStore between 60–90°F to maintain pot life and performance.\u003c\/li\u003e\n  \u003cli\u003eWear gloves while mixing; use a respirator when sanding cured material.\u003c\/li\u003e\n  \u003cli\u003eCompare with other two-part epoxy fillers if you need alternate cure profiles or viscosities.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho this product is for: TotalBoat TotalFair is aimed at boat owners, restorers and DIY marine technicians who want a high-strength, lightweight fairing compound that sands to a smooth, pinhole-free finish. It suits anyone needing waterproof, durable repairs on a range of materials—whether you’re patching a hull, smoothing a deck, or filling dings on vehicles and RVs. Professionals and experienced hobbyists will appreciate the fast cure, easy mixing and flexible adhesion, while weekend DIYers will value the simple 1:1 mixing and the product’s ability to stay put on vertical surfaces.\u003c\/p\u003e\n\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Can I use TotalFair below the waterline?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. Cured TotalFair is waterproof and bonds to common boat materials for use above or below the waterline.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Do I need a special primer before gelcoat?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes. Apply TotalBoat 2-Part Epoxy Primer or TotalProtect barrier coat before gelcoat; direct gelcoat over TotalFair will not cure properly.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"TotalBoat","offers":[{"title":"Default Title","offer_id":67584961708217,"sku":"B00LLL9FU8","price":188.14,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0822\/3765\/3177\/files\/totalboat-totalfair-front-packaging.jpg?v=1790461150","url":"https:\/\/redleafauto.ca\/products\/totalboat-totalfair-epoxy-fairing-compound-2-quart-kit-1-1-mix-fast-sanding-marine-putty","provider":"Redleaf Auto","version":"1.0","type":"link"}