Anina WPT928 Heated/Cooled Seat Wiring Harness - 12-Lead OEM-Fit ABS Connector, 12.36-inch Length

Anina WPT928 is a direct replacement 12-lead wiring harness that restores heated and cooled seat module connectivity for many Ford, Lincoln and Mercury vehicles.

If the factory seat climate control connector on your vehicle has melted, corroded, or failed, this Anina wiring kit gives you the correct pigtail and connector to repair the circuit quickly without replacing the entire module. Designed to match OEM fit and function, the harness uses durable ABS housing and pure copper conductors sized and colored for straightforward installation.

Which vehicles does this WPT928 wiring kit support?

The Anina WPT928 wiring assembly is built to be compatible with a wide range of Ford, Lincoln and Mercury models across multiple years. Fitment covers many F-Series trucks, Explorers, Taurus, Mustang, multiple Lincoln MK-series models, and Mercury Milan among others.

• Ford: F150 (2010–2017), F250/F350/F450/F550 Super Duty (2011–2019), Explorer (2011–2018), Expedition (2005–2017), Taurus (2010–2019), Mustang (2015–2017), Edge (2007–2018), Fusion (2006–2012), Flex (2013–2019), Police Interceptor and Special Service variants.
• Lincoln: MKC (2015–2019), MKS (2009–2016), MKT (2010–2019), MKX (2007–2015), MKZ (2007–2017), Navigator (2003–2017).
• Mercury: Milan (2006–2011) heated/cooled seat module support.
• OEM part numbers referenced: WPT928, WPT-928, 3U2Z-14S411-ZMB (use these when verifying fitment).

How durable and reliable is this replacement connector?

This harness is manufactured with an ABS plastic connector housing and pure copper wires to replicate OEM electrical performance. The cable length and wire gauge are chosen to provide mechanical strength while maintaining correct electrical resistance for seat heating and cooling circuits.

• Abrasion-resistant ABS connector shell for long-term use.
• Pure copper conductors for consistent conductivity and low voltage drop.
• 12.36-inch assembled cable length for access and routing under seats.
• Color-coded leads to match original wiring for easier installation.

How hard is it to install and what tools or guidance will I need?

Installation is designed to be completed in about an hour by someone comfortable with basic automotive wiring and seat removal. The pigtail plugs into the existing module and wires are matched to the vehicle harness; soldering or crimping may be required depending on your repair approach.

• Typical install time: under 1 hour for experienced DIYers.
• Tools commonly needed: trim tools, basic hand tools, crimpers or soldering iron, heat shrink or electrical tape.
• Color-code reference: consult online installation videos (search WPT928) for real-world routing tips.
• Check pin orientation and secure connector to prevent movement under the seat.

What does this wiring kit replace and what should I inspect during repair?

This kit replaces the pigtail connector and lead assembly that plugs into the heated/cooled seat climate control module. While swapping the harness, inspect the module pins and surrounding wiring for corrosion, melting, or shorted insulation to prevent repeat failures.

• Replace damaged pigtail plug housing and harness with WPT928 kit.
• Inspect module pins for bending, pitting, or overheating signs.
• Examine seat-bottom harness and connector routing for chafing.
• Secure and protect splice points with heat-shrink for durability.

Who is this for: The Anina WPT928 wiring kit is for DIY mechanics, professional automotive technicians and fleet service shops needing a direct, cost-effective replacement for a failed heated/cooled seat connector on supported Ford, Lincoln and Mercury vehicles. If your vehicle exhibits intermittent seat climate control, visible connector damage, or a burned plug, this harness provides the correct fit and materials to restore electrical connection and let you complete the repair without replacing the entire module.