ApplianPar Rear Arm Knuckle Bushings for Toyota & Lexus — 6‑Piece Rear Suspension Kit, Direct‑Fit Replacement

ApplianPar 6-piece rear arm knuckle bushing set restores rear suspension alignment and reduces play for compatible Toyota and Lexus 4WD models.

These rear arm knuckle bushings are engineered to replace worn rubber components that let the rear hub assembly move under load, helping maintain proper wheel geometry and a more controlled ride. The kit contains two bushing kits—each with three bushings—so you receive six parts total, matching the factory locations found on many Toyota and Lexus SUVs and sedans produced across the 1990s and 2000s. Designed as direct-fit replacements, they suit a wide range of platforms including RX, Highlander/ Kluger, Avalon, Camry/Vista, Harrier, Celica and several related chassis codes.

Which vehicles will these bushings fit?

This set covers numerous Toyota and Lexus applications across multiple years and drivetrain layouts, especially 4WD models and hybrid variants. Check your vehicle’s model code (e.g., MCU35, ACU25, MHU38) against the fitment list before ordering to ensure compatibility.

• Lexus RX300/330/350 MCU35/GSU35 (4WD) and RX400H MHU38 (4WD)
• Highlander/Kluger ACU25/MCU25 (2000–2007), MCU28 (2003–2007), HV MHU28 (2005–2007)
• Avalon GSX30 (2005–2007), MCX20 (1999–2004) and Camry/Vista SV30/CV30/VZV30, SV40/CV40
• Harrier/Harrier hybrid ACU35/MCU35/GSU35/MHU38 and various Celica, Carina ED, Corona Exiv related models

How will installing these bushings affect rear suspension performance?

Replacing fatigued or cracked bushings reduces excessive rear-wheel movement and restores more consistent alignment under braking and cornering. You can expect improved steering response from the rear axle and reduced clunks or vibration originating from the knuckle area when bushings are the worn component.

• Restores factory clearance and bushing preload
• Reduces hub knock and rear-end looseness
• Helps maintain camber/toe settings under load
• Direct-fit design simplifies swap during suspension service

What’s included in the package and what tools are helpful for installation?

The package ships as two separate bushing kits, three bushings per kit, totaling six rear arm knuckle bushings. Basic suspension tools and a press or appropriate sized sockets are recommended to remove the old bushings and install the new ones safely without damaging the knuckle.

• 2 x Bushing kits (3 bushings per kit) — 6 bushings total
• Recommended tools: hydraulic press or bushing driver, torque wrench, jack and stands
• Typical service: remove hub/knuckle assembly, press out old bushings, press in new bushings
• Inspect related hardware (bolts/arms) and replace if corroded

Are these bushings OEM or aftermarket, and do they need additional parts?

These ApplianPar bushings are aftermarket replacements designed to match factory dimensions and fitment points. Depending on condition, you might also replace adjacent suspension items (bolt kits, control arms, seals) during a comprehensive repair to ensure longevity and correct alignment.

• Aftermarket direct-fit parts, modeled for OEM compatibility
• May require new suspension bolts or hardware if originals show wear
• Not a full hub-bearing or knuckle assembly—bushings only
• Professional installation recommended for press-fit procedures

Who is this for: owners or mechanics servicing mid-2000s Lexus RX and Toyota Highlander/Cluger families, owners maintaining older Avalon or Camry platforms, and anyone restoring ride quality on Harrier, Celica or related chassis. If you notice rear suspension play, uneven tire wear, or hear clunks from the rear knuckle area, this six-piece bushing set offers a cost-effective way to restore resistance to movement and support correct wheel alignment.